亚洲AV色无码乱码在线观看|?愛妃?av中文字幕无码|最新国产91精品第二页|精品免费国产a级奶水

用于各種pom、聚甲  醛  、賽鋼料、pom賽鋼料、電木、電泳、pa尼龍塑料、改良性塑料、電泳、pom賽鋼料、uv表面及pcb線路板表面絲印及移印，不需加固化劑  ，不需烘烤，即可獲得優異的附著力。 油墨特性： 1、平光、附著力佳、耐汽油、耐化學品； 2、手感好，流平性佳、面光潔； 3、表面硬度好，耐沖擊性能強、抗刮傷； 4、耐汽油、耐酒精、耐化學品程度佳； 印刷： 選用網目為100-350目，以120t網紗計算涂覆蓋面積每公斤達30~35㎡。 表干時間自然揮發5-15分鐘，實干時間在24小時以內，48小時后達優秀性能。 1．用配套專用稀釋劑  開油水 2．用718洗網水洗網。 3．或添加配套硬化劑  10％可增加附著力,提高墨膜硬度。 4．烤箱80℃烘烤10分鐘佳能更優。 測試方法（完全干燥后）： 1．3m膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。 使用方法： 1．建議用我公司專用稀釋劑  進行稀釋，不建議使用783慢干稀釋劑  稀釋，使用前應充分?jǐn)嚢�，用后隨時密封。 2．?dāng)嚢钑r加本公司配套開油水10-12％，稀釋到印刷適合粘度，移印稀釋使用移印專用稀釋劑  ；用718洗網水清洗。 3．不得與其它類型油墨混合使用，否則容易出現其他附著力，化學反應等不良現象。 4. 加入固化劑  的油墨使用時限為8小時，過期請棄用，剩余油墨不可回收 注意事項： 1．各種承印物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。 2．在移印過程中，如出現拉絲或散開，可適當加入一些慢干膏即可; 3．環境溫度過高，將會影響油墨原有質量。白色超越150都會變色，烘烤時請用木質材料墊底進行烘烤，不得直接接觸鐵 4．根據氣候變化，請遠離火源，陰暗處15度-30度環境下存放pom steel material silk screen printing ink

for a variety of pom, poly formaldehyde, steel material, pom steel material, bakelite, electrophoresis, pa nylon plastic, modified plastics, electrophoresis, pom steel material, uv surface【敏感詞】pcb circuit board surface screen printing【敏感詞】printing, do not need to add curing agent,【敏感詞】does not need to bake, can obtain excellent adhesion. ink characteristics: 1, gloss, adhesion, good gasoline resistance, chemical resistance; 2, good hand feeling, good leveling, smooth surface; 3, good surface hardness, strong shock resistance, anti scratch; 4, gasoline resistance, alcohol resistance, chemical resistance【敏感詞】good; printing: choose mesh is 100-350 mesh, with 120t gauze calculation coated area coverage per kilogram of 30 to 35 square meters. table dry time natural volatile 5-15 minutes, hard work time within 24 hours, 48 hours after the best performance. 1 with matching special thinner open oil water 718 with 2 washing net. 3【敏感詞】adding matching hardening agent 10％ can increase adhesion, improve the ink film hardness. 4 oven 80 degrees bake 10 minutes canon better. test method (dry): 1.3m gummed paper hundred grid ink surface angle of 45 degrees quickly pulled off the oil painting. usage: 1 recommended to use my company's special diluent dilution, do not recommend the use of 783 slow dry dilution dilution, before use should be fully stirred, sealed at any time after use. 2. mixing cabernet companies supporting open water10-12％【敏感詞】dilution to printing for viscosity, printing the dilution used printing special thinner; with 718washing network water cleaning. 3 shall not be mixed with other types of ink,【敏感詞】else it is prone to other adhesion, chemical reactions【敏感詞】other undesirable phenomena. 4. add the curing agent of ink usage time is 8 hours【敏感詞】expired please abandoned【敏感詞】the remaining ink not recycling matters needing attention: 1. all kinds of printing material similar in appearance, but may be different materials, customers need to try printing【敏感詞】ensure its requirements,【敏感詞】then a batch production. 2. in the printing process, such as drawing【敏感詞】spread can be appropriate to add some slow dry paste can; 3 the ambient temperature is too high, will affect the ink the original quality. white beyond 150 color, please use woodiness material bottom baking baking shall not be in direct contact with the iron. according to the climate change, please stay away from fire, shadows 15 degrees-30 degrees environment storage